Hi ... I understand that every time my canvas hub connects with a different number of your wifi address. Now I know and I look for it every time it changes .... or if you don't like it you can give a fixed address to its port, so it won't change and you will connect directly every time (ex: 198.168.1.20 .... for example try to put 20 and look for it with the same address 20!) Come on, don't give up at the first difficulty ... you'll see that there will be others! Always ask for support and you will see that someone will help you! Luckily it is a hobby and not a job and therefore you take difficulties more calmly, otherwise it becomes more torture than a pastime! I am a woman and I came there alone .... if you do not get discouraged and you can look at the difficulties as fascinating challenges (like the rubik's cube) you will see that even the difficult things will fascinate you! Let us know how it goes! Hello
I can import and use the Canvas.io GCode in my slicing Repieter Host as I did before to restart the print from the interruption Layer, but I can't find the Layer in Maf and modify it or I can't find it in the Canvas Hub .mfc file . How do you recognize the Layer levels in Maf intended for the sd? Do I have to look at the time spent to change the cuts? I would like to know how the command to cut the .maf file works Io posso importare utilizzare il GCode di Canvas.io nel mio slicing Repieter Host come facevo prima a far ripartire la stampa dal Layer di interruzione, non so però trovare il Layer in Maf e modificarlo o non rieco a ritrovarlo nel file .mfc di Canvas Hub. Come si riconoscono i livelli Layer in Maf destinati alla sd? Devo guardare il tempo trascorso per modificare i tagli? Vorrei sapere come lavora il comando di taglio il file .maf
If I really could ask what I would like: I would like not to stress myself to change the page when I have to set the temperature of the extruder and then change the page to extrude .... then I would not want to change the page and then check the progress of the print in the gcode look. then always there on the same page, temperature control, print end time, immediate stop of the extruder motors in case of problems, without having to wait for Palette to decide to switch off the print with ease ... but really immediate. It would be very convenient to have separate x, y, z movement keys on this single page, with separate return to base. Ultimately I would like the convenience of Repieter Host slicing to be reproduced where everything is much more convenient. And if there was a language package for translation, it would be perfect! Thanks
After countless (many, many) splice cutting tests on Palette I have chosen to use the combination PLA PLA 5 4 5 and for the first time I have obtained a print without breaking joints during the path towards the extruder ... being careful however to block the tube on the motor so that the new weak filament for the junctions could not undergo dangerous oscillations. Good luck!
But do you have Canvas Hub? After turning Canvas Hub, Palette and my printer back on, I was having a hard time reconnecting and seeing the canvas hub network in my pc's connections. Now I find Canvas Hub much easier by typing the I.P. of my network http: //192.168.1.x, which I found by opening my network in the modem and staring, instead of typing http: //xxxx-xx-canvas-hub.local. Maybe you can use this experience of mine!
I would like to have on the same page of Canvas Hub the extrusion key together with the xyz movement controls and also the gcode drawing that is created during printing ... it would be very important to lighten the movements without changing the page while checking the situation and while Palette starts and 3d printing.
But do you have Canvas Hub? After turning Canvas Hub, Palette and my printer back on, I was having a hard time reconnecting and seeing the canvas hub network in my pc's connections. Now I find Canvas Hub much easier by typing the I.P. of my network http: //192.168.1.x, which I found by opening my network in the modem and staring, instead of typing http: //xxxx-xx-canvas-hub.local. Maybe you can use this experience of mine!
I am using Tronxy A8 with Palette S and Canvas Hub S. They seem ok together .... and I also had the problem of printing at 70% .... checking I noticed that the keychain in Canvas.io before cutting, is lower than the printing surface and therefore perhaps the lower value compared to the plane had escaped me ... I don't know why. Have you checked if the print is below the floor level? Let me know! Ciao
I'm using Tronxy A8 with Palette S and Canvas Hub S. They seem ok together .... maybe if you can't automate the heating, it would be better to have the motion controls buttons on the same page with the extruder controls, to avoid changing the page after turning on the extruder to get the filament out when Palette requires it .... just like the buttons in mine practical Repieter Host! I hope that over time it can be achieved!
Ciao…. I also have a Tronxy A8 printer connected with CANVAS HUB S and PALETTE S2 ....... however and after a while, ESPECIALLY after updating Palette with LATEST AVAILABLE DRIVERS, it started not listening to commands anymore! Do you think I may also need the FIRMWARE you recommended to him? So I figured I should update my Palette by removing plugins and firmware and updates that I have installed. I would like to start over, but I don't know what the right steps are after factory settings - do you have recommendations on run-out, ENDURANCE, etc. After these choices it all happened, while I was using the RANDOM mode to create filaments of multiple colors. He hasn't listened to commands since! I have performed a factory reset several times. ...but nothing! Palette extracts the filament for meters and meters, it doesn't cut it and it doesn't stop! .... even with the usual two-tone test keychain file I used earlier. I found the news in a guide that in accessory mode (I use Canvas Hub) the Palette with RUN OUT...
Hello ... I wanted to add to the list that my Tronxy A8 printer, as it is similar to the Anet A8, is compatible with Palette 2S and Canvas Hub. At the moment we found ... with the help and kindness of the Mosaic guys, that my Palette 2 S has a faulty switch. They are sending me the replacement. Congratulations to them and to you… who help us with your precious guides so as not to make mistakes. Live a colorful world thanks to you and to Mosaic !!!!
I am using Tronxy A8 with Palette S and Canvas Hub S. They seem ok to me .... but maybe I need dedicated firmware and plugins? Where do i find them? Does anyone have the same equipment as me? How do you find?
Ciao ... I saw in the video that the 4 drivers turn on simultaneously to recall the filament and then Palette asks for the 1st filament. To me, on the other hand, even after the factory settings reset, only the first drive turns on during calibration and then inserting the filament it doesn't stop anymore and nothing else happens! Help
Hi ... I saw in the video that the 4 drivers turn on simultaneously to recall the filament and then Palette asks for the 1st filament. To me, on the other hand, even after the factory settings reset, only the first drive turns on during calibration and then inserting the filament it doesn't stop anymore and nothing else happens! Help
Grazie Alina…sono riuscita a trovare il venditore. Ora vorrei sapere se posso avere la lingua in italiano sia in Palette che in Canvas Hub. Grazie ancora per i consigli che mi puoi dare. Ciao
Salve sto cercando un negozio che vende il dispositivo Palette della Mosaic in ITALIA per implementare la stampante 3D che uso per insegnamento e che vorrei pagare con la carta docente. Dove la potrei comprare in Italia in modo che mi possano valutare il buono? Grazie per l'aiuto che mi potrà fornire! nonvivedo@gmail.com
Hello ... I wanted to add to the list that my Tronxy A8 printer, as it is similar to the Anet A8, is compatible with Palette 2S and Canvas Hub. At the moment we found ... with the help and kindness of the Mosaic guys, that my Palette 2 S has a faulty switch. They are sending me the replacement. Congratulations to them and to you… who help us with your precious guides so as not to make mistakes. Live a colorful world thanks to you and to Mosaic !!!!
I am using Tronxy A8 with Palette S and Canvas Hub S. They seem ok to me .... but maybe I need dedicated firmware and plugins? Where do i find them? Does anyone have the same equipment as me? How do you find?
Ciao ... I saw in the video that the 4 drivers turn on simultaneously to recall the filament and then Palette asks for the 1st filament. To me, on the other hand, even after the factory settings reset, only the first drive turns on during calibration and then inserting the filament it doesn't stop anymore and nothing else happens! Help
Hi ... I saw in the video that the 4 drivers turn on simultaneously to recall the filament and then Palette asks for the 1st filament. To me, on the other hand, even after the factory settings reset, only the first drive turns on during calibration and then inserting the filament it doesn't stop anymore and nothing else happens! Help
Grazie Alina…sono riuscita a trovare il venditore. Ora vorrei sapere se posso avere la lingua in italiano sia in Palette che in Canvas Hub. Grazie ancora per i consigli che mi puoi dare. Ciao
Salve sto cercando un negozio che vende il dispositivo Palette della Mosaic in ITALIA per implementare la stampante 3D che uso per insegnamento e che vorrei pagare con la carta docente. Dove la potrei comprare in Italia in modo che mi possano valutare il buono? Grazie per l'aiuto che mi potrà fornire! nonvivedo@gmail.com