Printer Compatibility with Palette
Please refer to the following table to check your printer's compatibility with Palette 3. Palette has 3 requirements for compatibility: accepts non-proprietary filament which is 1.75 mm in diameter, recognizes files sliced in Slic3r/PrusaSlicer or CANVAS, and has open access to filament feed. If your printer is not listed in the table below, please reach out to support@mosaicmfg.com and we can confirm if it is compatible.
The CANVAS Hub (S) has two requirements for compatibility: a USB-B port and compatibility with OctoPrint - please check here if your printer is compatible with OctoPrint.
Make | Models | Accepts non-proprietary 1.75mm Filament | Material Compatibility | Uses supported file format | Compatible with Palette | Notes |
---|---|---|---|---|---|---|
3D Systems | CubePro (+ Duo, Trio) | Yes | Yes | No (.cubepro) | No | Proprietary filament and filetype. |
3DKreator | Motion | Yes | Yes | Yes | Yes | |
3DMakerWorld | Artifex, 2 | Yes | Yes | Yes | Yes | |
Afinia | H800, H479 | Yes | Yes | Yes | Yes | |
Airwolf3D | AXIOM 20 Dual Direct Drive | No | Yes | Yes | No | 2.85 mm |
Alfawise | U20 | Yes | Yes | Yes | Yes | |
Anet | A6, A8 | Yes | Yes | Yes | Yes | |
Anycubic | Delta, Kossel Plus, Chiron, Mega-s, i3-Mega, 4Max | Yes | Yes | Yes | Yes | |
Artillery | Sidewinder X1 | Yes | Yes | Yes | Yes | |
ATOM3DP | ATOM 2.0 | Yes | Yes | Yes | Yes | |
BCN3D | Sigma R17, R19 | No | Yes | Yes | No | Uses 2.85 mm filament; may be able to switch hot end |
BEEVERYCREATIVE | BEETHEFIRST, BEETHEFIRST+, BEEINSCHOOL, helloBEEprusa | Yes | Yes | Yes | Yes | |
Blackbelt-3D | Blackbelt | Yes | Yes | ? | No | Uses special version of Cura for slanted bed. Currently not compatible due to slanted print bed |
BQ | Hephestos 2, Witbox 1, Witbox 2 | Yes | Yes | Yes | Yes | |
CEL | Robox | Yes | Yes | No | No | Proprietary file type. |
Cetus | Cetus3D | Yes | Yes | Yes | Yes | Firmware uses different Z-axis properties. |
Cocoon Create | Touch, Model Maker | Yes | Yes | Yes | Yes | |
CoLiDo | X3045, M2020, 2.0+, Compact, DIY | Yes | Yes | Yes | Yes | |
CraftUnique | Craftbot | Yes | Yes | Yes | Yes | |
Creality | CR-10, Ender 3, 5 (Pro, S) | Yes | Yes | Yes | Yes | |
CreatBot | DE Plus, DX - Doble Dyser, DX Plus Doble Dyser | Yes | Yes | Yes | Yes | 3mm Bowden, but can print 1.75. |
CTC Ltd | Bizer, II, III, CTC-3D | Yes | Yes | Yes | Yes | |
Cubicon | Single (and Single Plus) | Yes | Yes | Yes | Yes | |
Cultivate3D | The Beast | Yes | Yes | Yes | Yes | |
Dagoma | Discovery 200, DiscoEasy 200 | Yes | Yes | Yes | Yes | |
Deezmaker | Bukito | Yes | Yes | Yes | Yes | |
Deltaprintr | Delta Go | Yes | Yes | Yes | Yes | |
Dremel | Dremel 3D20, 3D40, 3D45 | Yes | Yes | Yes | Yes | |
Dynamo3D | ONE-PRO | No | Yes | Yes | No | 2.85 mm |
FABtotum | Personal Fabricator | Yes | Yes | Yes | Yes | |
Febtop Tech | Optimus | Yes | Yes | Yes | Yes | |
Felix | 3L, Pro 1, Pro 2 | Yes | Yes | Yes | Yes | |
Flashforge | Adventurer, Creator, Creator Pro, Dreamer, Finder, Guidar (I & II) | Yes | Yes | Yes | Yes | CANVAS Hub has only been shown to work with the Creator Pro at this time using the GPX plugin for OctoPrint. Will not be able to work with Palette 3 in Connected Mode |
FLSUN3D | Kossel Delta, Prusa i3, Large Print Area | Yes | Yes | Yes | Yes | |
FLUX | Delta | Yes | Yes | Yes | Yes | |
Flying Bear | P902 | Yes | Yes | Yes | Yes | |
Folger Tech | Cloner, RepRap 2020, FT-5 | Yes | Yes | Yes | Yes | |
Formbot | T-Rex 1, 2, 2+ | Yes | Yes | Yes | Yes | |
Fusion3 | F400, F410 | Yes | Yes | Yes | Yes | |
gCreate | gMax 1.5+ | Yes | Yes | Yes | Yes | |
Geeetech | i3, Rostock 301 | Yes | Yes | Yes | Yes | |
German RepRap | X400 Pro | Yes | Yes | Yes | Yes | |
GP3D | Root, Root Plus | Yes | Yes | Yes | Yes | |
GTMax3D | Core A3, A1 | Yes | Yes | Yes | Yes | |
Hatchbox | Alpha | Yes | Yes | Yes | Yes | |
HE3D | Ei3 | Yes | Yes | Yes | Yes | |
Hesine 3D | M-505-B | Yes | Yes | Yes | Yes | |
HIC Technology | Hictop 3DP-17 | Yes | Yes | Yes | Yes | |
IMADE3D | Jellybox | Yes | Yes | Yes | Yes | |
Instone | Inventor Pro | Yes | Yes | Yes | Yes | |
JennyPrinter3 | Extended, Z360 | Yes | Yes | Yes | Yes | |
JGAurora | Z603S | Yes | Yes | Yes | Yes | |
KLIC-N-PRINT | 3D Printer | Yes | Yes | Yes | Yes | |
Kodak | Portrait | Yes | Yes | Yes | Yes | |
Kodama | Trinus | Yes | Yes | Yes | Yes | |
Leapfrog | Creatr | Yes | Yes | Yes | Yes | |
Leon3D | Lion Pro 3D | Yes | Yes | Yes | Yes | |
LulzBot | Mini, TAZ 5, TAZ 6 | Yes | Yes | Yes | Yes | LulzBot Conversion Kit |
M3D | M3D Pro, Micro | Yes | Yes | Yes | Yes | |
Makeit, Inc. | Pro-L, Pro-M | Yes | Yes | Yes | Yes | |
MakerBot | Replicator 2, Z18, Replicator +, 5th Gen | Yes | Yes | Yes | Yes | |
MakerFarm | Pegasus | Yes | Yes | Yes | Yes | |
MakerGear | M2, M3 | Yes | Yes | Yes | Yes | |
Malyan Systems | M200 | Yes | Yes | Yes | Yes | |
Mass Portal | Pharaoh ED, Pharaoh XD | Yes | Yes | Yes | Yes | |
MatterHackers | Pulse (XE) | Yes | Yes | Yes | Yes | |
MeCreator | 2 | Yes | Yes | Yes | Yes | |
MendelMax | 3.0 | Yes | Yes | Yes | Yes | |
Monoprice | MP Select Mini, Maker Select, Ultimate | Yes | Yes | Yes | Yes | |
Neo | 3D | Yes | Yes | Yes | Yes | |
New Matter | MOD-t | Yes | Yes | Yes | Yes | |
Omni3D | Factory 2.0 | No | No | Yes | No | |
PowerSpec | Pro, Pro 2, Ultra | Yes | Yes | Yes | Yes | |
Prenta | Duo, Duo XL | Yes | Yes | Yes | Yes | |
Printrbot | New Simple Pro, Play, Plus, Simple Metal | Yes | Yes | Yes | Yes | |
Prusa | MK2, MK3, MK3S, Mini | Yes | Yes | Yes | Yes | |
Qidi Tech | Tech 1, Tech X-one, X-Max | Yes | Yes | Yes | Yes | |
R3Dit | R3D-335/20 | Yes | Yes | Yes | Yes | |
Raise3D | N1, N2, N2+, Pro2, Pro2 Plus | Yes | Yes | Yes | Yes | |
RigidBot | Big | Yes | Yes | Yes | Yes | |
Robo 3D | R1, R1 Plus, C2, R2 | Yes | Yes | Yes | Yes | |
SeeMeCNC | Rostock MAX, v2, v3, Artemis 300 | Yes | Yes | Yes | Yes | |
Sethi3D | S3 | Yes | Yes | Yes | Yes | |
Shining 3D | EinStart-S, EinStart-L | Yes | Yes | No | No | Proprietary software (3dStart). |
Sindoh | 3DWOX DP200, DP201 | Yes | Yes | Yes | Yes | |
Snapmaker | Snapmaker | Yes | Yes | Yes | Yes | |
Solidoodle | Solidoodle 4 | Yes | Yes | Yes | Yes | |
Sovol | SV01 | Yes | Yes | Yes | Yes | |
SpiderBot | v2.2 Standard, Pro | Yes | Yes | Yes | Yes | |
Startt | 3D printer | Yes | Yes | Yes | Yes | |
TEVO | Black Widow, Delta, Tarantula i3 | Yes | Yes | Yes | Yes | |
Tiertime (pp3dp) | UP Box | Yes | Yes | Yes | Yes | |
Tinkerine | Pro, Plus | Yes | Yes | Yes | Yes | |
TRILAB | DeltiQ | Yes | Yes | Yes | Yes | |
Tronxy | P802E, X3 | Yes | Yes | Yes | Yes | |
Type A Machines | Series 1, Series 1 Pro | Yes | Yes | Yes | Yes | |
Ultibots | D300VS | Yes | Yes | Yes | Yes | |
Ultimaker | Ultimaker 2, 2go, Ultimaker 3, 3+, S5 | Yes | Yes | Yes | Yes | Ultimaker 1.75 mm adapter kit |
Velleman | K8400 Vertex, Vertex Nano | Yes | Yes | Yes | Yes | |
Volumic | Stream 30, Dual | Yes | Yes | Yes | Yes | |
Wanhao | Duplicator i3, 4S, 6, 9 | Yes | Yes | Yes | Yes | |
WASP | Delta 2040, 4070, 60100 | Yes | Yes | Yes | Yes | |
Wisemaker | W200 | Yes | Yes | Yes | Yes | |
Wombot | Exilis, Modus | Yes | Yes | Yes | Yes | |
XYZprinting | 1.0 AiO, Pro, 3-in-1, da Vinci 1.1 Plus, Jr. 1.0 Pro | Yes (would need to bypass chip system) | Yes | Yes | Yes | |
Yuchu | Yuchu-D 3D, Yuchu-W 3D, Pro | Yes | Yes | Yes | Yes | |
Z-Morph | 2.0 SX | Yes | Yes | Yes | Yes | |
Zinter | Architect, Home, Pro II, Zintable | Yes | Yes | Yes | Yes | |
Zonestar | D802, D805 | Yes | Yes | Yes | Yes | |
Zortrax | M200 | No | Yes | Yes | Yes | Proprietary filament and uses ZCode. Not yet compatible, but perhaps in the future. |
ZYYX | ZYYX+ | Yes | Yes | Yes | Yes |
155 Comments
Hello. I was wondering if the palette 2 is compatible with the ender 3 V3 se. If so, is the stock printer ok, or do modifications need to be made to the hardware or firmware?
Thank you
Aiden Mather - Reply
Hi Aiden, yes, we are compatible with this printer, there's no modifications need! You can find more information here: mm3d.co/firstprint
Jonny Yeu -
Does it work with ankermake m5c
Tommy - Reply
Hi Tommy,
Thank you for your interest in Palette! Regarding your question about Palette's compatibility with the Ankermake M5C I am happy to let you know that it is compatible.
Palette has three compatibility requirements for potential printers: They must use non-proprietary filament; the filament has to be 1.75mm in diameter; and it needs to be compatible with Canvas or PrusaSlicer, if you are using the P2PP plugin - Please note: Palette can only be used with these two slicers.
Rhesa Alleyne -
Does it work with k1max
William Arrington - Reply
Hi William,
I am happy to inform you that Creality's K1 Max is compatible with Palette however, because it does run on Klipper it is only compatible with Accessory Mode. In accessory mode, palette’s splicing and the printer’s execution of the G-Code are separate. A file is sent to Palette to create splices, while the G-Code is sent to the printer using a compatible method or storage device (e.g. over WiFi, USB drive, microSD/SD card).
Rhesa Alleyne -
I have a Anycubic Kobra Max 2 and its not connecting to the palette 3 pro
Luis LOPEZ - Reply
Hi Luis, please send us an email at support@mosaicmfg.com and we can troubleshoot this issue with you.
Jonny Yeu -
Where are the steps to make the palette 2s work with a creality k1 max...
mykeone - Reply
Hey mykeone, please follow the steps here: https://mm3d.co/firstprint
Jonny Yeu -
Is Palette 3 Pro compatible with Anker's Ankermake M5 In Connected Mode?
Tyler - Reply
Hey Tyler, we haven't been able to test this specific combination, but based on the specs, it does look to be compatible at least in Accessory mode.
Jonny Yeu -
The issue is that the USB port is in a mode to only accept usb devices it reads and a display (specifically at least the M5C for the display). Both do not work with solutions that allow for pausing, unless it has been physically verified. It is likely the ability to gcode pause the device would be unrecognized due to it wouldn’t communicate with anything other than specified. The Mosiac line would likely not work unless verified with the manufacturer. My opinion of this is from upon further research with other solutions. This is only my opinion and is not an official answer. Your mileage may vary.
glenn -
Hi I have a creality ender 3 with a direct drive installed. Would this still work for me?
Thanks
SURAJ - Reply
Yes, we would be compatible!
Jonny Yeu -
Ankermake m5? Or m5c?
Glenn - Reply
Hi Glenn, we'd be compatible with both based on their specs.
Jonny Yeu -
Would this work with the Mingda Magician X2?
Ely - Reply
Hey Ely, based on the specs, we would be compatible with this printer.
Jonny Yeu -
Are you all compatible with the K1?
Jordan Brooks - Reply
Nobody has the steps to make it work in connected mode on a k1...
mykeone -
Hey Jordan, yes, we are compatible with the K1 printer.
Jonny Yeu -
Does this work with the Anycubic Kobra 2 Neo?
Ryan - Reply
Hey Ryan, yes, we would be compatible with this printer.
Jonny Yeu -
As this is an older post, I'll ask this question: will it work with Prusa mk4 and XL printers?
ColonelXZ - Reply
Yes, we're compatible with these printers in Accessory mode.
Jonny Yeu -
is this compatible with the bambu labs printers? (X1, P1P, etc) Thanks!
Bob - Reply
Yes, we are compatible with Bambu labs in accessory mode!
Jonny Yeu -
Is pallet compatible with QIDI x-plus ender 5s1 solvo sv04?
John C Sturtz - Reply
Yes, we are compatible with these printers!
Jonny Yeu -
Greetins, would a Palette 3 Pro be compatible with the Creality CR-M4?
Afonso - Reply
Hey Afonso, yes, we would be compatible with this printer.
Jonny Yeu -
It is compatible with printer running klipper firmware?
I own a tronxy xy-2 pro custom
(skr pro 1.2 Mainboard, stealthburner dual sensor print head, v6 hotend, ceramic heater)
Samuel Walter - Reply
Yes, we are compatible with Klipper printers via Accessory mode.
Jonny Yeu -
Is creatily k1 max compatible with palette 2s?
Thomasghislain - Reply
Yes, we would be compatible!
Jonny Yeu -
is it compatible with SP-5 corexy 3d printer made by Twotrees?
Jason - Reply
Yes, we would be compatible with this printer.
Jonny Yeu -
Hello, is this compatible with Anker's Ankermake M5 3D printer?
Alex Ruiz - Reply
Yes, we are compatible with this printer.
Jonny Yeu -
Is it compatible with the Sovol SV06 and SV06 Pro?
Lynn - Reply
Hi Lynn, yes we are compatible with these printers.
Jonny Yeu -
Hi, does Palette compatible with Bambu x-1 carbon?
Tianyu Xing - Reply
Yes, we would be compatible with this printer.
Jonny Yeu -
Hi ,
Palette 3Pro can be connected via usb cable to ender 3v2 ? Or just accessory mode ?
Racz Zoltan - Reply
Yes, we can run in Connected mode with the Ender 3V2 printer.
Jonny Yeu -
Hello, I have a problem connecting Deltiq 2 Plus to Palette 3, I have a Canvas account setup, Palette added, and the Printer functioning properly. The printer is not recognized by auto-connect. Please help me set up the printer and Palette.
Artem Yakupov - Reply
Hi Artem, I see your message in our inbox and will respond through your e-mail thread.
Jonny Yeu -
Hello, does Palette 3 Pro works with the QiDi X-CF Pro ?
f3g4t0 - Reply
Yes, we are compatible with this printer!
Jonny Yeu -
Is it compatible with creality ender 3 S1 PRO?
Luciano Andre Schmitt - Reply
Hi Luciano, yes, we would be compatible.
Jonny Yeu -
When will you be fully compatible with AnyCubic Kobra MAX?
tomcollick - Reply
Hey there, yes, we are fully compatible with this printer.
Jonny Yeu -
Does pallette 3 pro works with the creality cr-10 smart pro?
Kim Jensen - Reply
Hi Kim, yes, we are compatible with this printer.
Jonny Yeu -
Is the palette 3 compatible with the cr-5 pro high temperature?
Charles Lafollette - Reply
Hey Charles, based on the specs for this printer, we would be compatible.
Jonny Yeu -
I bought my pallette 3 pro to use with the Cr-30 - print mill - has anyone modified the canvas to allow this as yet ? I dont use either anywhere as much as i should do as they wont talk.
David Smith - Reply
We’re currently not compatible with print mill style printers unless you’re using the non-calibration modes (multi-spool, gradient, random, pattern).
Jonny Yeu -
How do I use Creality 10S with Pallette 3 pro?
tomcollick - Reply
Hey tomcollick, I would recommend using the preset CR-10 profile and make any changes to the physical differences (bed size, Bowden tube length) between the models. Everything else would be the same.
Jonny Yeu -
Is the Palette 3 compatible with CR10 Smart or Anycubic Kobras ?
Chris Sloan - Reply
Hi @crusher17, the specifications for both of these printers look to be compatible. I would recommend creating a printer profile in Canvas3d.io to become familiar with slicing for Palette, and to test print quality in single color.
Adalyn Ordono -
Is Palette 3 compatible with the Anycubic Mega Zero 2.0? If so, is it set for Bowden tube or direct drive?
Aaron Croy - Reply
Yes, we would be compatible with this printer in both Bowden and Direct Drive setups. If you’re running it in a Bowden style setup, you’d just need to add a Bowden tube length in your printer profile: mm3d.co/bowden
Jonny Yeu -
Ever thought about trying to make it work with Printers with belts like the Infinity3D so we can do some printing farms
Snake - Reply
Sadly I don’t have a 3D printer….. Yet…. It’s one of my short term goals to clean out my back room that is currently acting like a storage room and making that my 3D printer room. I’d like something where I wanna print multiple colors (cause I SUCK at art so I’m not a good painter) which is why I’m here and something can auto print the same thing over and over again cause I got some young cousins and you probably know how kids are. As soon as one gets something all of them want it lol
Snake -
Thanks for sharing! We haven’t tested with this printer in the past, but it seems that we could be compatible. If you have this printer, you could try and process a file from Canvas to see if it would read the GCode properly.
Jonny Yeu -
But the Infinity3D isn’t like your average belt printer. it HAS the option to do that 45 degree printing but you don’t have to. See https://www.youtube.com/watch?v=luGLYK4V...
Snake -
Currently, the restriction is on the software side of things as were unable to create a transition tower on belt style printers. However, you would be able to use non-calibrated style prints like Random, Pattern, Gradient, and Multi-Spool mode with belt printers.
Jonny Yeu -
Can you confirm the compability with an Ender 3 S1? It is significantly different that previous Ender 3’s. Also can you comment on the compatibility on a QIDI i-fast? I understand it would only work with one nozzle if it does.
Patrick Martin - Reply
Hey Patrick, we would be compatible with the Ender 3 S1 as it still fulfills the compatibility criteria. You’d also be correct that while we are compatible with the QIDI i-fast, it would only print with one nozzle at a time.
Jonny Yeu -
Hello, will the Palette 3 Pro work with the Creality Ender 3 S1 printer and also with the Snapmaker 2.0 A350 printer?
Ronald Hunter - Reply
Hi Ronald, we’re compatible with the Ender is both Accessory and Connected mode while we’d only be compatible in Accessory mode with the A350.
Jonny Yeu -
Will the palette 3 pro work with klipper firmware printer(Voron2.4)?
Patrick Yeung - Reply
Yes, Palette is compatible with the Voron2.4 via Accessory mode: mm3d.co/p3-accessory
Jonny Yeu -
Hi, does Elegoo Neptune 2 could work with Palette 3?
Ashley Song - Reply
Hi Ashley, yes, we are compatible with this printer.
Jonny Yeu -
Hi there, I see that it’s compatible with the Sidewinder X1, but is it compatible with the new Sidewinder X2?
Alexander Robinson - Reply
Hi @arobinson96, taking a look at the extruder and the specifications, it looks to be compatible as well.
Adalyn Ordono -
Will this work with the Elegoo Neptune 2s?
Steve - Reply
Yes, we are compatible with this printer
Jonny Yeu -
Will this work on the Creality Ender 3 Pro?
Eugene Van Deest - Reply
Yes, we are compatible with the Ender 3 Pro
Jonny Yeu -
Hi, may I confirm if it is compatible with the Creality Ender-7 3D Printer? Thanks.
Kay - Reply
Hey Kay, yes we are compatible with the Ender 7
Jonny Yeu -
Would it be possible to use this with Ender 6?
Dorian - Reply
Yes, we are compatible with this printer
Jonny Yeu -
Hello, I am interested in getting the Flashforge Adventurer 4 and then later purchasing the Palette 3 Pro for it but I am confused about the compatibility. In the comments above it said it was compatible but in the list above it says “CANVAS Hub has only been shown to work with the Creator Pro at this time using the GPX plugin for OctoPrint.” Sorry I am newbie can you clarify this for me.
Jennifer Vujtech - Reply
Hey Jennifer, this information pertains to Palette 2 and Canvas Hub. For Palette 3, it would be compatible with the Adventurer 4 without any additional plugins needed.
Jonny Yeu -
Just bought the Tronxy X5SA-600 (600x600x600) printer. Is Pallet 3 compatable?
Dennis K Lamb - Reply
Hi Dennis, yes we are compatible with this printer.
Jonny Yeu -
Will this work with the Elegoo Neptune?
Steve - Reply
Hey Steve, based on its specs, it is compatible.
Jonny Yeu -
Hi there, is the P3 compatible with the Monoprice MP Voxel 3D?
Alexander Robinson - Reply
Hey Alexander, it looks like this printer uses a proprietary print software, do you know if it works with files created in Simplify3D, KISSlicer, or Slic3r?
Jonny Yeu -
Hi! I want to ne sure if your mozaic pro3 is compatible with my CR10S and my Zortrax M200
Patrick - Reply
Hi Romain, P3 is compatible with the CR10S but not the Zortrax as it uses a proprietary ZCode print file.
Jonny Yeu -
Hello, i have a ender 5 and want to use the palette 2S Pro. Will this work??
Roland - Reply
Yes, we are compatible with the Ender 5 printer
Jonny Yeu -
Will it work with flashforge adventurer 3 or 4
Sam - Reply
Yes, we are compatible with this printer.
Jonny Yeu -
Will palette work with BigTreeTech motherboard Octopus based printers? Have a big DIY build that I would like to use the palette with.
Michael D - Reply
Yes, as long as it fulfills the criteria of accepting non-proprietary filament which is 1.75 mm in diameter, recognizing files sliced in S3D, Cura, KISSlicer, Slic3r/Prusa Slicer, or CANVAS, and having open access to filament feed.
Jonny Yeu -
Will the Palette 3 Pro work with FORMBOT VIVEDINO CORE XY Fully Enclosed 3D Printer with Orbiter V1.5 Direct Drive Extruder? Link:https://www.formbot3d.com/products/vived...
Josh Cook - Reply
Hey Josh, yes we’d be compatible with this printer.
Jonny Yeu -
Is this compatible with the FlashForge Creator Pro 2 with IDEX?
Ryan Sumner - Reply
Hey @rizzle710, yes we are compatible with Flashforge Creator Pro 2, but with only one extruder at a time.
Adalyn Ordono -
Is this compatible with the new Anycubic Vyper?
Marc - Reply
Hey Marc, yes we are compatible with this printer!
Jonny Yeu -
Anet 8+ or Anet ET5x or Sunlu S8 compatible?
Ken Pon - Reply
Hi @msdt207025, all three of these printer models look to be compatible!
Adalyn Ordono -
Is is compatible with creality CR20s-Pro? Thank you.
Kerri - Reply
Yes, it is compatible with this printer!
Alina -
Does pallette 3 pro works with the creality cr10s pro v2? Thanks for the help
Shikuruu - Reply
Yes, it will!
Alina -
With the Titan Direct Drive on the Creality CR-10 V3, will the Palette system still work?
Thomas vonAhlefeld - Reply
Hi Thomas, yes Palette will work on this setup as well.
Alina -
Hello ... I wanted to add to the list that my Tronxy A8 printer, as it is similar to the Anet A8, is compatible with Palette 2S and Canvas Hub. At the moment we found ... with the help and kindness of the Mosaic guys, that my Palette 2 S has a faulty switch. They are sending me the replacement. Congratulations to them and to you… who help us with your precious guides so as not to make mistakes. Live a colorful world thanks to you and to Mosaic !!!!
VIVEDO3D - Reply
Seeing that Ender 5 is compatible with the product, just wanting to confirm that the Ender 5 Plus is compatible as well. As well as if the need to change to a direct drive extruder is required or not.
Taylor Jacobs - Reply
Hey Taylor, Palette is compatible with the Ender 5 Plus as well. You do not need to change to a direct drive extruder - Palette works both on Bowden and direct drive setups (mm3d.co/firstprint).
Alina -
I am using Tronxy A8 with Palette S and Canvas Hub S. They seem ok to me .... but maybe I need dedicated firmware and plugins? Where do i find them? Does anyone have the same equipment as me? How do you find?
VIVEDO3D - Reply
Hi Vivdeo, you may need an OctoPrint plugin for your TronXY printer: https://github.com/OctoPrint/OctoPrint-F...
Jonny Yeu -
Are your products compatible with Tenlog TL-D3 Pro & Tenlog TL-D6 printers? Thanks!
Wasim - Reply
Hi Wasim, based on the specs of these printers, we would be compatible.
Jonny Yeu -
I see it is compatible with snapmaker, but what about snapmaker 2.0?
Aaron - Reply
Hi Aaron, Palette is compatible with the Snapmaker 2.0.
Alina -
Hi - i am Thomas
Is it compatible to the QIDI X-Plus? Does it work as QIDI X-Pro?
Thomas Quappe - Reply
Hey Thomas, Palette is compatible with both of these printers.
Alina -
Zortrax m300 dual. I would love it if you could get the system to work with their code. Are there any plans to do this
Rob - Reply
Hey Rob, we do not have any set timelines on our end to work on this compatibility. However, we are working on creating GCode for multi extruder printers in the future.
Alina -
Is it compatible with the TENLOG Hands2?
Mark Cobbold - Reply
Hi Mark, yes this printer is compatible.
Jonny Yeu -
Are you compatible with the Min8 Kossel printer
Iain Selkirk - Reply
Hi Iain, yes this printer is compatible.
Jonny Yeu -
Thanks Alina, yes other slicers should be supported:
https://old.craftbot.com/forums/view-thr...
https://craftbot.com/software
I don’t have the printer yet but I wanted to prior confirm that it will work with your excellent product before buying.
Martin L - Reply
Thanks for sending that over, we can confirm that it is compatible with Palette. Please let us know if you have any more questions!
Alina -
Hi!
Are you compatible and tested with CRAFTBOT FLOW XL?
Martin L - Reply
Hey Martin, unfortunately it looks like this printer has its own slicer, CraftWare. If you can confirm that you are able to use either S3D, Cura, KISSlicer, PrusaSlicer, or CANVAS (our slicer) successfully with this printer, then we can confirm that it is compatible.
Alina -
Yes, we are compatible with the Da Vinci 1.0 Pro printer
Jonny Yeu - Reply
Is this compatible with the XYZ Printing Da Vinci 1.0 Pro?
Zachary Kinney - Reply
Hey Michael, we haven’t tested with the Method X, but currently it does not seem to be compatible since it doesn’t allow for non-proprietary filament.
Jonny Yeu - Reply
How about a Makerbot Method X? Couldn’t you utilize the auxiliary ports?
Michael D - Reply
@dankerg Hey Dany, yes, we are also compatible with the Qidi X-Plus.
Alina - Reply
Is this also compatible with qidi x plus ?
Dany Kerger - Reply
Hi Scott, yes, we are compatible with the Qidi XMax printer.
Jonny Yeu - Reply
I have a Qidi Xmax, will you system work with it?
Scott reynolds - Reply
Yes, we are compatible with this printer, but please note that we may not be compatible with some of the materials that it prints. For more information, please see our multi-material guide: mm3d.co/mm
Jonny Yeu - Reply
Is this compatible with the AON M2V1?
Andy Egtberts - Reply
Hi @andy, it looks to be compatible with regards to the material diameter and file output used. One item to consider is if there is a location on the filament feed or extruder, where an extruder clip for Palette can be attached. A PTFE tube is connected between Palette and the extruder during printing. We provide a clip for this tube to stay secure, or one can be designed for the printer following these guidelines.
Adalyn Ordono -
Hi KingWazzack, yes we are compatible with the Ender 5 Plus printer.
Jonny Yeu - Reply
Is this product compatible with the Creality Ender 5 Plus?
KingWazzack - Reply
Hey Cesar, currently, we’re not compatible with the M300 as it uses their own proprietary ZCode. There are GCode to ZCode converters available online, but we haven’t been able to test if these files as we don’t have a Zortrax in-house.
Jonny Yeu - Reply
Zortrax M300 is the printer i have I wanted to know if the I can get this to work with this model
Cesar Modesto - Reply