Printer Compatibility with Palette
Please refer to the following table to check your printer's compatibility with Palette 3. Palette has 3 requirements for compatibility: accepts non-proprietary filament which is 1.75 mm in diameter, recognizes files sliced in Slic3r/PrusaSlicer or CANVAS, and has open access to filament feed. If your printer is not listed in the table below, please reach out to support@mosaicmfg.com and we can confirm if it is compatible.
The CANVAS Hub (S) has two requirements for compatibility: a USB-B port and compatibility with OctoPrint - please check here if your printer is compatible with OctoPrint.
| Make | Models | Accepts non-proprietary 1.75mm Filament | Material Compatibility | Uses supported file format | Compatible with Palette | Notes |
|---|---|---|---|---|---|---|
| 3D Systems | CubePro (+ Duo, Trio) | Yes | Yes | No (.cubepro) | No | Proprietary filament and filetype. |
| 3DKreator | Motion | Yes | Yes | Yes | Yes | |
| 3DMakerWorld | Artifex, 2 | Yes | Yes | Yes | Yes | |
| Afinia | H800, H479 | Yes | Yes | Yes | Yes | |
| Airwolf3D | AXIOM 20 Dual Direct Drive | No | Yes | Yes | No | 2.85 mm |
| Alfawise | U20 | Yes | Yes | Yes | Yes | |
| Anet | A6, A8 | Yes | Yes | Yes | Yes | |
| Anycubic | Delta, Kossel Plus, Chiron, Mega-s, i3-Mega, 4Max | Yes | Yes | Yes | Yes | |
| Artillery | Sidewinder X1 | Yes | Yes | Yes | Yes | |
| ATOM3DP | ATOM 2.0 | Yes | Yes | Yes | Yes | |
| BCN3D | Sigma R17, R19 | No | Yes | Yes | No | Uses 2.85 mm filament; may be able to switch hot end |
| BEEVERYCREATIVE | BEETHEFIRST, BEETHEFIRST+, BEEINSCHOOL, helloBEEprusa | Yes | Yes | Yes | Yes | |
| Blackbelt-3D | Blackbelt | Yes | Yes | ? | No | Uses special version of Cura for slanted bed. Currently not compatible due to slanted print bed |
| BQ | Hephestos 2, Witbox 1, Witbox 2 | Yes | Yes | Yes | Yes | |
| CEL | Robox | Yes | Yes | No | No | Proprietary file type. |
| Cetus | Cetus3D | Yes | Yes | Yes | Yes | Firmware uses different Z-axis properties. |
| Cocoon Create | Touch, Model Maker | Yes | Yes | Yes | Yes | |
| CoLiDo | X3045, M2020, 2.0+, Compact, DIY | Yes | Yes | Yes | Yes | |
| CraftUnique | Craftbot | Yes | Yes | Yes | Yes | |
| Creality | CR-10, Ender 3, 5 (Pro, S) | Yes | Yes | Yes | Yes | |
| CreatBot | DE Plus, DX - Doble Dyser, DX Plus Doble Dyser | Yes | Yes | Yes | Yes | 3mm Bowden, but can print 1.75. |
| CTC Ltd | Bizer, II, III, CTC-3D | Yes | Yes | Yes | Yes | |
| Cubicon | Single (and Single Plus) | Yes | Yes | Yes | Yes | |
| Cultivate3D | The Beast | Yes | Yes | Yes | Yes | |
| Dagoma | Discovery 200, DiscoEasy 200 | Yes | Yes | Yes | Yes | |
| Deezmaker | Bukito | Yes | Yes | Yes | Yes | |
| Deltaprintr | Delta Go | Yes | Yes | Yes | Yes | |
| Dremel | Dremel 3D20, 3D40, 3D45 | Yes | Yes | Yes | Yes | |
| Dynamo3D | ONE-PRO | No | Yes | Yes | No | 2.85 mm |
| FABtotum | Personal Fabricator | Yes | Yes | Yes | Yes | |
| Febtop Tech | Optimus | Yes | Yes | Yes | Yes | |
| Felix | 3L, Pro 1, Pro 2 | Yes | Yes | Yes | Yes | |
| Flashforge | Adventurer, Creator, Creator Pro, Dreamer, Finder, Guidar (I & II) | Yes | Yes | Yes | Yes | CANVAS Hub has only been shown to work with the Creator Pro at this time using the GPX plugin for OctoPrint. Will not be able to work with Palette 3 in Connected Mode |
| FLSUN3D | Kossel Delta, Prusa i3, Large Print Area | Yes | Yes | Yes | Yes | |
| FLUX | Delta | Yes | Yes | Yes | Yes | |
| Flying Bear | P902 | Yes | Yes | Yes | Yes | |
| Folger Tech | Cloner, RepRap 2020, FT-5 | Yes | Yes | Yes | Yes | |
| Formbot | T-Rex 1, 2, 2+ | Yes | Yes | Yes | Yes | |
| Fusion3 | F400, F410 | Yes | Yes | Yes | Yes | |
| gCreate | gMax 1.5+ | Yes | Yes | Yes | Yes | |
| Geeetech | i3, Rostock 301 | Yes | Yes | Yes | Yes | |
| German RepRap | X400 Pro | Yes | Yes | Yes | Yes | |
| GP3D | Root, Root Plus | Yes | Yes | Yes | Yes | |
| GTMax3D | Core A3, A1 | Yes | Yes | Yes | Yes | |
| Hatchbox | Alpha | Yes | Yes | Yes | Yes | |
| HE3D | Ei3 | Yes | Yes | Yes | Yes | |
| Hesine 3D | M-505-B | Yes | Yes | Yes | Yes | |
| HIC Technology | Hictop 3DP-17 | Yes | Yes | Yes | Yes | |
| IMADE3D | Jellybox | Yes | Yes | Yes | Yes | |
| Instone | Inventor Pro | Yes | Yes | Yes | Yes | |
| JennyPrinter3 | Extended, Z360 | Yes | Yes | Yes | Yes | |
| JGAurora | Z603S | Yes | Yes | Yes | Yes | |
| KLIC-N-PRINT | 3D Printer | Yes | Yes | Yes | Yes | |
| Kodak | Portrait | Yes | Yes | Yes | Yes | |
| Kodama | Trinus | Yes | Yes | Yes | Yes | |
| Leapfrog | Creatr | Yes | Yes | Yes | Yes | |
| Leon3D | Lion Pro 3D | Yes | Yes | Yes | Yes | |
| LulzBot | Mini, TAZ 5, TAZ 6 | Yes | Yes | Yes | Yes | LulzBot Conversion Kit |
| M3D | M3D Pro, Micro | Yes | Yes | Yes | Yes | |
| Makeit, Inc. | Pro-L, Pro-M | Yes | Yes | Yes | Yes | |
| MakerBot | Replicator 2, Z18, Replicator +, 5th Gen | Yes | Yes | Yes | Yes | |
| MakerFarm | Pegasus | Yes | Yes | Yes | Yes | |
| MakerGear | M2, M3 | Yes | Yes | Yes | Yes | |
| Malyan Systems | M200 | Yes | Yes | Yes | Yes | |
| Mass Portal | Pharaoh ED, Pharaoh XD | Yes | Yes | Yes | Yes | |
| MatterHackers | Pulse (XE) | Yes | Yes | Yes | Yes | |
| MeCreator | 2 | Yes | Yes | Yes | Yes | |
| MendelMax | 3.0 | Yes | Yes | Yes | Yes | |
| Monoprice | MP Select Mini, Maker Select, Ultimate | Yes | Yes | Yes | Yes | |
| Neo | 3D | Yes | Yes | Yes | Yes | |
| New Matter | MOD-t | Yes | Yes | Yes | Yes | |
| Omni3D | Factory 2.0 | No | No | Yes | No | |
| PowerSpec | Pro, Pro 2, Ultra | Yes | Yes | Yes | Yes | |
| Prenta | Duo, Duo XL | Yes | Yes | Yes | Yes | |
| Printrbot | New Simple Pro, Play, Plus, Simple Metal | Yes | Yes | Yes | Yes | |
| Prusa | MK2, MK3, MK3S, Mini | Yes | Yes | Yes | Yes | |
| Qidi Tech | Tech 1, Tech X-one, X-Max | Yes | Yes | Yes | Yes | |
| R3Dit | R3D-335/20 | Yes | Yes | Yes | Yes | |
| Raise3D | N1, N2, N2+, Pro2, Pro2 Plus | Yes | Yes | Yes | Yes | |
| RigidBot | Big | Yes | Yes | Yes | Yes | |
| Robo 3D | R1, R1 Plus, C2, R2 | Yes | Yes | Yes | Yes | |
| SeeMeCNC | Rostock MAX, v2, v3, Artemis 300 | Yes | Yes | Yes | Yes | |
| Sethi3D | S3 | Yes | Yes | Yes | Yes | |
| Shining 3D | EinStart-S, EinStart-L | Yes | Yes | No | No | Proprietary software (3dStart). |
| Sindoh | 3DWOX DP200, DP201 | Yes | Yes | Yes | Yes | |
| Snapmaker | Snapmaker | Yes | Yes | Yes | Yes | |
| Solidoodle | Solidoodle 4 | Yes | Yes | Yes | Yes | |
| Sovol | SV01 | Yes | Yes | Yes | Yes | |
| SpiderBot | v2.2 Standard, Pro | Yes | Yes | Yes | Yes | |
| Startt | 3D printer | Yes | Yes | Yes | Yes | |
| TEVO | Black Widow, Delta, Tarantula i3 | Yes | Yes | Yes | Yes | |
| Tiertime (pp3dp) | UP Box | Yes | Yes | Yes | Yes | |
| Tinkerine | Pro, Plus | Yes | Yes | Yes | Yes | |
| TRILAB | DeltiQ | Yes | Yes | Yes | Yes | |
| Tronxy | P802E, X3 | Yes | Yes | Yes | Yes | |
| Type A Machines | Series 1, Series 1 Pro | Yes | Yes | Yes | Yes | |
| Ultibots | D300VS | Yes | Yes | Yes | Yes | |
| Ultimaker | Ultimaker 2, 2go, Ultimaker 3, 3+, S5 | Yes | Yes | Yes | Yes | Ultimaker 1.75 mm adapter kit |
| Velleman | K8400 Vertex, Vertex Nano | Yes | Yes | Yes | Yes | |
| Volumic | Stream 30, Dual | Yes | Yes | Yes | Yes | |
| Wanhao | Duplicator i3, 4S, 6, 9 | Yes | Yes | Yes | Yes | |
| WASP | Delta 2040, 4070, 60100 | Yes | Yes | Yes | Yes | |
| Wisemaker | W200 | Yes | Yes | Yes | Yes | |
| Wombot | Exilis, Modus | Yes | Yes | Yes | Yes | |
| XYZprinting | 1.0 AiO, Pro, 3-in-1, da Vinci 1.1 Plus, Jr. 1.0 Pro | Yes (would need to bypass chip system) | Yes | Yes | Yes | |
| Yuchu | Yuchu-D 3D, Yuchu-W 3D, Pro | Yes | Yes | Yes | Yes | |
| Z-Morph | 2.0 SX | Yes | Yes | Yes | Yes | |
| Zinter | Architect, Home, Pro II, Zintable | Yes | Yes | Yes | Yes | |
| Zonestar | D802, D805 | Yes | Yes | Yes | Yes | |
| Zortrax | M200 | No | Yes | Yes | Yes | Proprietary filament and uses ZCode. Not yet compatible, but perhaps in the future. |
| ZYYX | ZYYX+ | Yes | Yes | Yes | Yes |
113 Comments
Hi, does Palette compatible with Bambu x-1 carbon?
Tianyu Xing - Reply
Yes, we would be compatible with this printer.
Jonny Yeu -
Hi ,
Palette 3Pro can be connected via usb cable to ender 3v2 ? Or just accessory mode ?
Racz Zoltan - Reply
Yes, we can run in Connected mode with the Ender 3V2 printer.
Jonny Yeu -
Hello, I have a problem connecting Deltiq 2 Plus to Palette 3, I have a Canvas account setup, Palette added, and the Printer functioning properly. The printer is not recognized by auto-connect. Please help me set up the printer and Palette.
Artem Yakupov - Reply