Palette 3 (Pro) has 3 requirements for compatibility:
- printer uses non-proprietary filament
- printer uses 1.75 mm filament
- printer is compatible with Canvas or PrusaSlicer, if you are using the P2PP plugin - Palette 3 Pro can only be used with these two slicers
If your printer is not on this list and you are not sure if it meets the compatibility requirements, please contact us at support@mosaicmfg.com.
Make | Models | Accepts non-proprietary 1.75mm Filament | Material Compatibility | Uses supported file format | Compatible with Palette | Notes |
---|---|---|---|---|---|---|
3D Systems | CubePro (+ Duo, Trio) | Yes | Yes | No (.cubepro) | No | Proprietary filament and file type |
3DKreator | Motion | Yes | Yes | Yes | Yes | |
3DMakerWorld | Artifex, 2 | Yes | Yes | Yes | Yes | |
Afinia | H800, H479 | Yes | Yes | Yes | Yes | |
Airwolf3D | AXIOM 20 Dual Direct Drive | No | Yes | Yes | No | 2.85 mm |
Alfawise | U20 | Yes | Yes | Yes | Yes | |
Aon 3D | M2+ | Yes | Yes | Yes | Yes | |
Anet | A6, A8 ET5 Pro | Yes | Yes | Yes | Yes | |
Anycubic | Delta, Kossel Plus, Chiron, Mega-s, i3-Mega, Mega X, 4Max, Kobra, Kobra Max, Vyper | Yes | Yes | Yes | Yes | |
Artillery | Sidewinder X1, X2, Genius Pro | Yes | Yes | Yes | Yes | |
ATOM3DP | ATOM 2.0 | Yes | Yes | Yes | Yes | |
BCN3D | Sigma R17, R19 | No | Yes | Yes | No | Uses 2.85 mm filament; may be able to switch hot end |
BEEVERYCREATIVE | BEETHEFIRST, BEETHEFIRST+, BEEINSCHOOL, helloBEEprusa | Yes | Yes | Yes | Yes | # |
BIQU | B1 | Yes | Yes | Yes | Yes | |
Blackbelt-3D | Blackbelt | Yes | Yes | No | Uses special version of Cura for slanted bed. Currently not compatible due to slanted print bed | |
CEL | Robox | Yes | Yes | No | No | Proprietary file type |
Cetus | Cetus3D | Yes | Yes | Yes | Yes | Firmware uses different Z-axis properties |
Cocoon Create | Touch, Model Maker | Yes | Yes | Yes | Yes | |
CoLiDo | X3045, M2020, 2.0+, Compact, DIY | Yes | Yes | Yes | Yes | |
CraftUnique | Craftbot | Yes | Yes | Yes | Yes | |
Creality | CR (6 SE, 6 Max, 10, 10S, 10 Max, 10 V3, 10S Pro, 10S Pro V2, 20 Pro, 200-B); Ender (3, 3 V-2, 3 Pro, 3 Max, 3X, 3 Pro X, 3 S1, 3 S1 Pro, 3 S1 Plus, 3 V2 Neo, 5 Plus, 5 Pro, 6, 7); Sermoon D1 | Yes | Yes | Yes | Yes | Please note that while you can use Palette in multi, random, or gradient mode with belt printers, they are not compatible for calibrated prints |
CreatBot | DE Plus, DX - Doble Dyser, DX Plus Doble Dyser | Yes | Yes | Yes | Yes | 3 mm Bowden, but can print 1.75 |
CTC Ltd | Bizer, II, III, CTC-3D | Yes | Yes | Yes | Yes | |
Cubicon | Single (and Single Plus) | Yes | Yes | Yes | Yes | |
Cultivate3D | The Beast | Yes | Yes | Yes | Yes | |
Dagoma | Discovery 200, DiscoEasy 200 | Yes | Yes | Yes | Yes | |
Deezmaker | Bukito | Yes | Yes | Yes | Yes | |
Deltaprintr | Delta Go | Yes | Yes | Yes | Yes | |
Dremel | Dremel 3D20, 3D40, 3D45 | Yes | Yes | Yes | Yes | Can only be used in accessory mode. Dremel uses .g3drem file - select this in printer profile on Canvas. |
Dynamo3D | ONE-PRO | No | Yes | Yes | No | Uses 2.85 mm filament |
Elegoo | Neptune 3 | Yes | Yes | Yes | Yes | |
Febtop Tech | Optimus | Yes | Yes | Yes | Yes | |
Felix | 3L, Pro 1, Pro 2 | Yes | Yes | Yes | Yes | |
Flashforge | Adventurer (1 & 2), Creator, Creator Pro, Dreamer, Finder, Guider (I & II) | Yes | Yes | Yes | Yes | Can only be used in accessory mode |
Flashforge | Adventurer 4 | Yes | Yes | Yes (.gx) | Yes | Compatible with accessory mode |
FLSUN3D | Kossel Delta, Prusa i3, Large Print Area, (SR) Super Racer, V400 | Yes | Yes | Yes | Yes | |
FLUX | Delta | Yes | Yes | Yes | Yes | |
Flying Bear | P902 | Yes | Yes | Yes | Yes | |
Folger Tech | Cloner, RepRap 2020, FT-5 | Yes | Yes | Yes | Yes | |
Formbot | T-Rex 1, 2, 2+, Trodoon | Yes | Yes | Yes | Yes | With Trodoon: would need to mount Palette above printer to access filament feed, and disable filament sensor |
Fusion3 | F400, F410 | Yes | Yes | Yes | Yes | |
gCreate | gMax, gMax 1.5+ | Yes | Yes | Yes | Yes | |
Geeetech | i3, Rostock 301 | Yes | Yes | Yes | Yes | |
German RepRap | X400 Pro | Yes | Yes | Yes | Yes | |
GTMax3D | Core A3, A1 | Yes | Yes | Yes | Yes | |
Hatchbox | Alpha | Yes | Yes | Yes | Yes | |
HE3D | Ei3 | Yes | Yes | Yes | Yes | |
HIC Technology | Hictop 3DP-17 | Yes | Yes | Yes | Yes | |
IMADE3D | Jellybox | Yes | Yes | Yes | Yes | |
Intamsys | Funmat HT | Yes | Yes | Yes | Yes | |
JennyPrinter3 | Extended, Z360 | Yes | Yes | Yes | Yes | |
JGAurora | Z603S | Yes | Yes | Yes | Yes | |
JGMaker | Artist-D Pro | Yes | Yes | Yes | Yes | |
Kingroon | KP3S | Yes | Yes | Yes | Yes | |
Kodak | Portrait | Yes | Yes | Yes | Yes | |
Leapfrog | Creatr | Yes | Yes | Yes | Yes | |
Leon3D | Lion Pro 3D | Yes | Yes | Yes | Yes | |
Longer | LK5 Pro | Yes | Yes | Yes | Yes | |
LulzBot | Mini, TAZ 5, TAZ 6 | No | Yes | Yes | No | Uses 2.85 mm filament |
Makeit, Inc. | Pro-L, Pro-M | Yes | Yes | Yes | Yes | |
MakerBot | Replicator 2, Z18, Replicator +, 5th Gen | Yes | Yes | Yes | Yes | |
MakerFarm | Pegasus | Yes | Yes | Yes | Yes | |
MakerGear | M2, M3, M3-ID | Yes | Yes | Yes | Yes | With M3-ID, Palette would only be able to use one of the extruders at a time. |
Malyan Systems | M200 | Yes | Yes | Yes | Yes | |
Mass Portal | Pharaoh ED, Pharaoh XD | Yes | Yes | Yes | Yes | |
MatterHackers | Pulse (XE) | Yes | Yes | Yes | Yes | |
MeCreator | 2 | Yes | Yes | Yes | Yes | |
MendelMax | 3.0 | Yes | Yes | Yes | Yes | |
Mingda | Magician Pro | Yes | Yes | Yes | Yes | |
Modix | Big-60, Big-Meter | Yes | Yes | Yes | Yes | |
Monoprice | MP Select Mini, Maker Select, Ultimate | Yes | Yes | Yes | Yes | |
Neo | 3D | Yes | Yes | Yes | Yes | |
Omni3D | Factory 2.0 | No | No | Yes | No | |
PowerSpec | Pro, Pro 2, Ultra | Yes | Yes | Yes | Yes | |
Printrbot | New Simple Pro, Play, Plus, Simple Metal | Yes | Yes | Yes | Yes | |
Prusa | MK2, MK2.5, MK3, MK3S(+), Mini (+) | Yes | Yes | Yes | Yes | |
Qidi Tech | i-Fast, i-Mate, Tech 1, Tech X-one, X-Max, X-CF Pro, X-Plus | Yes | Yes | Yes | Yes | Currently can only be used in accessory mode. With dual extruder printers, Palette can only use one extruder at a time. |
Raise3D | E2, N1, N2, N2+, Pro2, Pro2 Plus, Pro 3 | Yes | Yes | Yes | Yes | Pro 3 can only be used in accessory mode. |
Robo 3D | R1, R1 Plus, C2, R2 | Yes | Yes | Yes | Yes | |
SeeMeCNC | Rostock MAX, v2, v3, Artemis 300 | Yes | Yes | Yes | Yes | |
Sethi3D | S3 | Yes | Yes | Yes | Yes | |
Shining 3D | EinStart-S, EinStart-L | Yes | Yes | No | No | Proprietary software (3dStart) |
Sindoh | 3DWOX DP200, DP201 | Yes | Yes | Yes | Yes | |
Snapmaker | Snapmaker | Yes | Yes | Yes | Yes | |
Sovol | SV01, SV03, SV04 | Yes | Yes | Yes | Yes | |
SpiderBot | v2.2 Standard, Pro | Yes | Yes | Yes | Yes | |
Startt | 3D printer | Yes | Yes | Yes | Yes | |
TEVO | Black Widow, Delta, Tarantula i3 | Yes | Yes | Yes | Yes | |
Tiertime (pp3dp) | UP Box | Yes | Yes | Yes | Yes | |
Tinkerine | Pro, Plus | Yes | Yes | Yes | Yes | |
TRILAB | DeltiQ, DeltiQ 2 | Yes | Yes | Yes | Yes | |
Tronxy | P802E, X3, Gemini, X5SA Pro | Yes | Yes | Yes | Yes | |
Two Trees | Sapphire Pro | Yes | Yes | Yes | Yes | |
Ultimaker | Ultimaker 2, 2go, Ultimaker 3, 3+, S5 | No | Yes | Yes | No | Uses 2.85 mm filament |
Velleman | K8400 Vertex, Vertex Nano | Yes | Yes | Yes | Yes | |
Volumic | Stream 30, Dual | Yes | Yes | Yes | Yes | |
Voron | 2.4 R2 | Yes | Yes | Yes | Yes | Can be used in accessory mode only, due to Klipper firmware |
Voxelab | Aquila S2 | Yes | Yes | Yes | Yes | |
Wanhao | Duplicator i3, 4S, 6, 9 | Yes | Yes | Yes | Yes | |
WASP | Delta 2040, 2040 Pro, 4070, 60100 | Yes | Yes | Yes | Yes | |
Wisemaker | W200 | Yes | Yes | Yes | Yes | |
XYZprinting | 1.0 AiO, Pro, 3-in-1, da Vinci (1.1 Plus, Super, mini w+) da Vinci Jr. (1.0 Pro, WiFi Pro) | Yes (would need to bypass chip system) | Yes | Yes | Yes | |
Yuchu | Yuchu-D 3D, Yuchu-W 3D, Pro | Yes | Yes | Yes | Yes | |
Z-Morph | 2.0 SX | Yes | Yes | Yes | Yes | |
Zonestar | D802, D805 | Yes | Yes | Yes | Yes | |
Zortrax | M200 | No | Yes | Yes | No | Proprietary filament and uses ZCode. Not yet compatible, but perhaps in the future |
ZYYX | ZYYX+ | Yes | Yes | Yes | Yes |
86 Comments
Hello.
1. Is it possible to use Palette 3 with a printer not listed here and with a different slicer?
2. Is there any page where the exact setup is described (e.g. where the models are uploaded and what is controlled by what)?
3. Is there any chance the splice core can be purchased and used separately? E.g. I'm primarily interested in splicing a new spool automatically when an existing spool runs out.
Raman - Reply
Hey Raman, to answer your questions:
1. The printer would be compatible as long as the printer fits the criteria (non-proprietary 1.75 mm filament, using either Canvas or PrusaSlicer. We wouldn't be compatible with any other slicers at this time.
2. We have a setup article here (mm3d.co/p3-firstprint). If you're wondering about how Palette stays in calibration with your printer, we have information on the system here (mm3d.co/ping-pong)
3. You can purchase replacement splice cores, but it would not be able to be used separate from Palette (mm3d.co/spare-parts). If you're interested in splicing spools, there is Multi-Spool mode (mm3d.co/p3-multispool).
Jonny Yeu -
Are there any belt printers on the market that are compatible with calibrated printing for the Palette 3 Pro?
Robbie McNatt - Reply
Not at the moment. The reason for this is that there is no slicer that would be capable of producing the proper files for Palette at the moment.
Jonny Yeu -
Will the palette pro 3 work with Creality’s CR-30?
Robbie McNatt - Reply