Articles in this section

Using Chroma with Palette 2

Avatar
Jonny Yeu
  • Updated
Follow

With Chroma V3.1 and newer, you will now have the option of creating files for your Palette 2 (Pro) along with the Palette/Palette+ capabilities offered in the past. This would only be used if you would prefer to use one of our supported slicers (Simplify3D, Cura, KISSlicer, Slic3r) instead of using CANVAS. Please note: as CANVAS is capable of slicing and creating print files for your Palette and printer, you would not need to use Chroma or another slicer in combination with CANVAS.

Get Chroma here.

 

Creating a new Printer Profile

When you first create a printer profile for Chroma, you will now have the option to choose between Palette/Palette 2 and Palette 2 (Pro).

  1. In Chroma, select Profiles > Printer Profiles > New Profile
  2. Once you've selected your printer, you'll need to select your Palette Type.
  3. If Palette 2 (Pro) is selected, you'll be able to select if a CANVAS Hub is connected (Connected Mode) or if you're using your Palette without a CANVAS Hub (Accessory Mode).

ChromaP2.png

 

Editing your printer profile

  1. In Chroma, select Profiles > Printer Profiles > Edit for your printer.
  2. Select the Palette tab.
  3. You'll be able to select the Palette Type. If Palette 2 (Pro) is selected, you'll be able to select if a CANVAS Hub is connected (Connected Mode) or if you're using your Palette without a CANVAS Hub (Accessory Mode).

Chromap2-1.png

 

Once this is set, Chroma will now create files for your printer and Palette 2 (Pro).

 

If you have any additional questions, please send us a message at support@mosaicmfg.com.

 

 

 

Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request

Comments

4 comments

Sort by Date Votes
  • Avatar
    IronHalo
    • Edited

    This looks great Jonny!  When will you be posting v3.1 for download?

    0
    Comment actions Permalink
  • Avatar
    Jonny Yeu

    Thanks! We'll have the update ready by the end of the week. Chroma will prompt you to update once everything is ready.

    0
    Comment actions Permalink
  • Avatar
    Korey MacGill

    Hello, i've been trying the 2 color keychain using chroma to slice up my gcode from cura, and i've had mixed results, after a few prints, i tried moving to a 4 color mario print ya'll have on thingiverse, and i just can't get any of the colors to work right. so i think my offsets really far off. 

     

    however when i went back to chroma to do another keychain, i noticed that the default settings that start up are now gone, since i've fiddled with them and experimented, where is the/ is there a "reset to default" button anywhere that will reset the prime tower settings to what it was when i first installed?

     

    much appreciated! this thing is such a fun journey!

    0
    Comment actions Permalink
  • Avatar
    Jonny Yeu

    Hey Korey, thanks for your message, I'm glad that you're enjoying the Palette experience so far! There's a few things I'd like to share with you:

    • If you're using Cura with Chroma, please follow the steps here (http://mm3d.co/cura). We've seen that newer versions of Cura add some additional GCode that can cause issues, so we'd recommend using V3.2-3.3 for best results
    • If you're having issues with color placement, it's likely an issue with calibration. If possible, could you please send us pictures of your keychain calibration print and the bottom of the transition tower? This can provide us with with information about your loading offset (http://mm3d.co/newkeychain-troubleshooting).
    • There's no way to reset the transition tower to the original position, but if you double click the transition tower, you'll enable the control settings where you can move the tower and adjust the dimensions:

    • If you're still experiencing issues, please feel free to e-mail us pictures of your prints and we can provide further assistance (support@mosaicmfg.com)!
    0
    Comment actions Permalink

Leave a comment

Related articles