Skip to main content

The world's first multi-material slicer.

239 Questions View all

Looking for Ender 5 Pro profile

Just purchased my Palette 2s, and I can’t find a profile for my Creality Ender 5 Pro. Do I use one of the other Creality printer profiles or create my own?

Answer this question I have this problem too

Is this a good question?

Score 2
Add a comment

4 Answers

Most Helpful Answer

Hi Roland, you can use the Ender 3 preset profile as a foundation for the Ender 5 and you’ll just need to make adjustments to the physical properties like the print bed area.

Was this answer helpful?

Score 2

Comments:

Thanks, could you help me out with the setting for extrution?? my ender with direct drive has a extrution (e-step) of 147.8mm (to get 100mm) but i cant find the right info to do so.

by

@roland78 I would recommend reviewing this article: https://mattshub.com/blogs/blog/extruder...

by

@jonnyyeu I have an Ender 5 Plus. Is there a prebuilt profile that works best with that (CR-10 or Ender 3)? If so, will all I need to change is the printer platform diminsions?

by

@jsmith100 I'd recommend using the Ender 3 preset profile, then update the bed dimensions and Bowden tube length

by

@jonnyyeu, thank you. I used the Ender 3 settings (changing the bed dimensions). I measured the Bowden tube (starting where the filament goes in to the Ender 5 Plus filament sensor down to the nozzle tip on the extruder (32 inches). I set the Bowden tube to 813mm (32" = 812.8mm). Started the key chain calibration print. 1st layer looks good, except right at the end of the 1st layer, the 2nd color starts extruding early... Something seems off, but I'm not sure where to address. I did tap the smart load button when loading the Ender 5, and had to manually pull a little filament from the tube so that I could run it through the sensor and into the drive gears... If that is the problem, is there a way to get ~3-4 inches sticking out of the end of the tube so that it is long enough to feed to extruder drive gears? I can send pictures. Thanks in advance for your time.

by

Show 22 more comments

Add a comment

Hey @stoneking24, thanks for reaching out about this and sorry for our delayed response due to the holidays. You can use the preset printer profile for the CR-10 on CANVAS; you only have to change any differences in physical dimensions, such as bed size. Please let us know if you have any questions!

Was this answer helpful?

Score 1
Add a comment

Can i use this profile fore the ender 5 also??

Was this answer helpful?

Score 1
Add a comment

Sorry that you did not test your Firmware before the release of v22.03.29.0 this is bad it would have facilitated a lot of work fr me... i had to go back to v22.02.09.0 and it wors fine!

Then to my Creality Ender 5 Plus which had everything in original I had to rebuild everything on my extruder holder nothing suited for your tube holder.

And there was no USB cable that was for my printer…

It is now only in the morning hours that I have been able to run my first print on keychain...

i saw that the Temeraturen on the Printer is set to 210 Degrees and 60 on the bedd this is something that i can change ??,

Would rather have had 200/0 on the bed works best on my printer with PLA... tried to change in P3 but it changes back with no choice to save...

Kindly

Christer Persson

Was this answer helpful?

Score 0

Comments:

Hey Christer, temperature settings are found in your project settings under Temperature and Cooling

by

Hi Jonny Yeu!

Thank you very much, had a little hard to find it. :)

by

Add a comment

Add your answer

Adam will be eternally grateful.
View Statistics:

Past 24 Hours: 1

Past 7 Days: 2

Past 30 Days: 15

All Time: 366

Contact Mosaic Support Team

© 2022 Mosaic Manufacturing Ltd.